How To Clean Robot Vacuum Brush Long Hairs

I had no idea how much hair was on our floors until we got our kickoff Roomba. Emptying our Roomba'due south bin for the offset fourth dimension, my family looked on in slack-jawed amazement as I pulled out fistfulls of hair, and that was merely from most half of our apartment.

The matter well-nigh all that hair is that it doesn't just go into the Roomba'southward dust bin. A surprising amount of hair gets wrapped around your Roomba's various brushes, and if you want to avoid permanent damage to your new robotic friend, you'll need to roll up your sleeves and pull the hair off.

The bad news about cleaning the hair off your Roomba'southward brushes is that y'all'll need to practice it regularly. Roomba recommends cleaning a Roomba's brushes once a calendar week, or even twice a calendar week if you have hairy pets. I admit that I don't quite go on to that schedule; instead, I average more like once a month, although we tend to just run our Roomba on a weekly footing. In whatever event, you'll want to make cleaning your Roomba'due south brushes a addiction.

The good news is that cleaning your Roomba'south brushes isn't too much of a hassle, peculiarly if y'all do it regularly. With my Roomba 675, I tin can go the job done in less than 10 minutes. As well, retrieve that yous're non going for perfection, but rather getting the most egregious clumps of pilus out of the mode.

I'll describe the cleaning procedure for the Roomba 675, one of the most popular Roomba models. If y'all take a dissimilar model, y'all can find detailed instructions on the iRobot support site, but the following steps will notwithstanding give you the gist.

Opening the brush guard

The first step is to put your Roomba upside-downwardly on a flat surface, preferably on a towel (which gets tossed in the hamper immediately subsequently the cleaning) or something else soft.

Just pull on the yellow latch to release your Roomba's castor guard.

You lot should at present run across a couple of thin cylindrical brushes, one with bristles and a second with long safety flaps. Keeping these brushes in identify is a baby-sit that you'll need to remove; just pull back on the ii yellowish levers to open up the baby-sit.

Related: Acquire how to make clean your Roomba's bin the correct way

Remove the brushes

Looking more closely at the brushes, yous'll see that each has a yellowish plastic bearing at each end. If you pull each brush up gently from the begetting finish, they should come up right out.

Once you pull the brushes out of your Roomba, you lot'll see all the hair that's wrapped around the beard and the plastic gasket. Time to commencement yanking!

On the other end of the brush is a gray, not-removable cap with a square-shaped peg that fits into a matching receptacle in the brush compartment; when you replace the brush, you lot'll desire to fit the cap into the receptacle earlier snapping the bearing terminate back in place.

Pull all the hair off

At present comes the fun part (and yes, your hands are about to get dingy). Starting with the bristle castor, remove the plastic bearing, and so pull off whatsoever pilus that's get wrapped around the bearing itself or tucked inside the bearing. The hair should come off pretty easily.

Likewise on the brush itself, you'll discover hair wrapped both effectually and inside the yellow gasket.

The same tin can't be said for the actual bristles; get ready to spend quality time yanking and pulling the hair out. Retrieve, you don't have to make clean off every last strand; the idea hither is to remove the worst clumps. Rinse and repeat (not literally!) for the second brush, which—despite its lack of beard—will still have a fair amount of pilus wrapped around it.

If you lot notwithstanding accept the lilliputian hair cleaning tool that came with your Roomba, by all means, use it. The tool looks similar a thick red ring with abrupt plastic teeth inside (be careful, those teeth tin can really poke your fingers).

Nevertheless have this picayune cleaning tool that came with your Roomba? Use it.

Ben Patterson/IDG

Simply pull the Roomba brush through the band, and then marvel as the tool absolutely tears through the pilus on the brush. Just a unmarried pass of the tool can yank an astonishing amount of hair.

This is how much hair came off my Roomba's brush afterward a unmarried pass with the tool.

Ben Patterson/IDG

All washed (or done enough, anyway)? Replace the brushes in the compartment (remember most plumbing fixtures the gray ends in first) and snap the castor guard back into identify.

Not perfect, but good enough.

If you lot take the fourth dimension and inclination, you might also want to gently wipe down the Roomba's brush compartment, which can go clumsily dusty over time. Whatever textile should practice, although I got expert results from using a dry Swiffer clothRemove non-product link.

Remove and clean the side brush

You're not quite done yet. Next, it's time to de-hair the side brush, that spindly-looking, tri-brush component that sweeps upward hard-to-reach dust, clay, and debris. Likewise being yellow, information technology'll be easy to spot, given that it'southward probably got a bunch of hair wrapped around it.

You can remove the Roomba's side brush with a regular or Phillips-caput screwdriver.

You can use a regular or Phillips-caput screwdriver to unscrew the side brush from the principal Roomba chassis; in one case y'all remove the screw, just pull the side castor straight out.

Related: How to clean a Roomba's charging contacts and cliff sensors

Now, getting the hair unwrapped from the side brush tin can be a chip of a chore. I've had the well-nigh success using a pair of scissors to snip the tightly wound hair, which should then exist fairly easy to pull abroad.

No more than pilus, or at to the lowest degree not until the next cleaning.

One time you're done yanking the hair off the side brush, go ahead and spiral it back onto the main Roomba unit.

Replacing your Roomba brushes

Besides regularly cleaning the brushes on your Roomba, you'll also need to replace them from time to fourth dimension.

iRobot recommends replacing the two primary brushes every six to twelve months. While iRobot doesn't offering a recommended timeline for replacing the delicate side brush, swapping in a new one every six months to a twelvemonth; I had to replace mine early after it was damaged during a cleaning.

Follow this linkRemove non-product link to store for replacement Roomba brushes on Amazon.

Cleaning the residual of your Roomba

The hairy brushes aren't the simply things you'll need to make clean on your Roomba. You should also clean its wheels on a regular basis.

As well, if your Roomba's battery is e'er running low or it keeps stopping in the centre of the floor, you should clean its charging surfaces and cliff sensors.

Finally, only elimination your Roomba's dust bin later each cleaning isn't enough. You should also make clean its filter, and hither's how to do it properly.

Thinking of buying a new robot vacuum? Check out our favorites right here

Note: When you purchase something after clicking links in our manufactures, we may earn a small commission. Read our chapter link policy for more details.

Ben has been writing about technology and consumer electronics for more than 20 years. A PCWorld contributor since 2022, Ben joined TechHive in 2022, where he covers smart speakers, soundbars, and other smart and dwelling house-theater devices. You can follow Ben on Twitter.

Source: https://www.techhive.com/article/579224/how-to-clean-the-brushes-on-a-roomba.html

Posted by: mileyclus1971.blogspot.com

Share this post